國立高雄大學圖資館 |

語系: 繁體中文

說明(常見問題)

圖資館首頁

登入

回首頁

切換: 標籤 | MARC模式 | ISBD

Resolution characterization and nano...

Chao, Weilun.

Resolution characterization and nanofabrication for soft X-ray zone plate microscopy.

紀錄類型:	書目-電子資源 : Monograph/item
正題名/作者:	Resolution characterization and nanofabrication for soft X-ray zone plate microscopy.
作者:	Chao, Weilun.
面頁冊數:	177 p.
附註:	Chair: David Attwood.
附註:	Source: Dissertation Abstracts International, Volume: 66-08, Section: B, page: 4386.
Contained By:	Dissertation Abstracts International66-08B.
標題:	Engineering, Electronics and Electrical.
電子資源:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3187000
ISBN:	9780542292118

Resolution characterization and nanofabrication for soft X-ray zone plate microscopy.
Chao, Weilun.

Resolution characterization and nanofabrication for soft X-ray zone plate microscopy. - 177 p.

Chair: David Attwood.

Thesis (Ph.D.)--University of California, Berkeley, 2005.

Soft x-ray microcopy is a valuable nano-imaging technique in a wide variety of scientific disciplines. It complements other nano-imaging techniques, such as electron and scanning probe microscopy, by offering a unique set of capabilities including elemental and chemical specificity, magnetization sensitivity, as well as in-situ imaging with applied fields, overcoatings, and wet environments. By combining these advantages with high spatial resolution, the full-field transmission microscope, XM-1, operating at wavelengths in the 1 nm to 3 nm range, has yielded valuable knowledge in many areas of the physical and life sciences. A key to optimizing its performance for nanoscale studies is quantitatively determining and maximizing the spatial resolution. In this dissertation, new methods are demonstrated which permit accurate characterization and significant improvement of the spatial resolution. Based on both theoretical and experimental studies of the existing measurement techniques (using test objects such as knife edge, e-beam fabricated test structures, etc.), a new technique that uses multilayer coatings in cross section has been developed, which was shown to provide a more accurate means in quantifying resolution. By imaging this multilayer test object, systematic measurement of the microscope's modulation response as a function of feature periods is demonstrated. The measurement results show that, for the microscope with an objective micro zone plate fabricated using conventional single exposure electron beam lithography, the resolution is near-diffraction-limited at 20 nm. This resolution is limited by the smallest zone width of the micro zone plate, which was limited by the electron beam lithography used for fabricating the zone plate. To obtain better resolution, a new overlay nanofabrication technique has been developed by the nanofabrication team at Lawrence Berkeley National Laboratory (LBNL). This technique, based on sequential fabrication of alternating zone structures, significantly reduces the smallest feature sizes e-beam lithography is capable of fabricating in dense patterns. Using this technique with the LBNL's Nanowriter electron beam writer, zone plates of 15 nm outermost zone width have been fabricated for the first time, with excellent zone placement accuracy of 1.7 nm. Characterization of the microscope using the multilayer test object indicates that sub-15 nm spatial resolution has been achieved with these zone plates.

ISBN: 9780542292118Subjects--Topical Terms:

226981
Engineering, Electronics and Electrical.

Resolution characterization and nanofabrication for soft X-ray zone plate microscopy.
LDR:03437nmm _2200253 _450 001 170802
005 20061228142249.5
008 090528s2005 eng d
020 $a 9780542292118
035 $a 00242832
040 $a UnM $c UnM
100 0 $a Chao, Weilun. $3 244833
245 1 0 $a Resolution characterization and nanofabrication for soft X-ray zone plate microscopy.
300 $a 177 p.
500 $a Chair: David Attwood.
500 $a Source: Dissertation Abstracts International, Volume: 66-08, Section: B, page: 4386.
502 $a Thesis (Ph.D.)--University of California, Berkeley, 2005.
520 # $a Soft x-ray microcopy is a valuable nano-imaging technique in a wide variety of scientific disciplines. It complements other nano-imaging techniques, such as electron and scanning probe microscopy, by offering a unique set of capabilities including elemental and chemical specificity, magnetization sensitivity, as well as in-situ imaging with applied fields, overcoatings, and wet environments. By combining these advantages with high spatial resolution, the full-field transmission microscope, XM-1, operating at wavelengths in the 1 nm to 3 nm range, has yielded valuable knowledge in many areas of the physical and life sciences. A key to optimizing its performance for nanoscale studies is quantitatively determining and maximizing the spatial resolution. In this dissertation, new methods are demonstrated which permit accurate characterization and significant improvement of the spatial resolution. Based on both theoretical and experimental studies of the existing measurement techniques (using test objects such as knife edge, e-beam fabricated test structures, etc.), a new technique that uses multilayer coatings in cross section has been developed, which was shown to provide a more accurate means in quantifying resolution. By imaging this multilayer test object, systematic measurement of the microscope's modulation response as a function of feature periods is demonstrated. The measurement results show that, for the microscope with an objective micro zone plate fabricated using conventional single exposure electron beam lithography, the resolution is near-diffraction-limited at 20 nm. This resolution is limited by the smallest zone width of the micro zone plate, which was limited by the electron beam lithography used for fabricating the zone plate. To obtain better resolution, a new overlay nanofabrication technique has been developed by the nanofabrication team at Lawrence Berkeley National Laboratory (LBNL). This technique, based on sequential fabrication of alternating zone structures, significantly reduces the smallest feature sizes e-beam lithography is capable of fabricating in dense patterns. Using this technique with the LBNL's Nanowriter electron beam writer, zone plates of 15 nm outermost zone width have been fabricated for the first time, with excellent zone placement accuracy of 1.7 nm. Characterization of the microscope using the multilayer test object indicates that sub-15 nm spatial resolution has been achieved with these zone plates.
590 $a School code: 0028.
650 # 0 $a Engineering, Electronics and Electrical. $3 226981
690 $a 0544
710 0 # $a University of California, Berkeley. $3 212474
773 0 # $g 66-08B. $t Dissertation Abstracts International
790 $a 0028
790 1 0 $a Attwood, David, $e advisor
791 $a Ph.D.
792 $a 2005
856 4 0 $u http://libsw.nuk.edu.tw:81/login?url=http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3187000 $z http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3187000