國立高雄大學圖資館 |

Language: English

Back

固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 = Effe...

國立高雄大學化學工程及材料工程學系碩士班

固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 = Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel

Record Type:	Language materials, printed : monographic
Paralel Title:	Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel
Author:	林承毅,
Secondary Intellectual Responsibility:	國立高雄大學
Place of Publication:	[高雄市]
Published:	國立高雄大學;
Year of Publication:	2015[民104]
Description:	[10]，109葉圖，表 : 30公分;
Subject:	13Cr2Mo2Ni不銹鋼
Subject:	13Cr2Mo2NiStainless Steel
Online resource:	https://hdl.handle.net/11296/76mn5y
Notes:	109年11月18日公開
Summary:	本論文研製之新型不銹鋼13Cr2Mo2Ni，欲將此材料應用螺絲製造業，針對其組織與硬度分析，研究適合加工的熱處理參數。本實驗分為兩個部分，第一部分為固溶化熱處理，此階段顯微組織主要為基地相的麻田散鐵，以及δ肥粒鐵相，在1100℃持溫時間30分鐘內時，仍有富硼富鉬相未固溶回基地中；在1100℃~1200℃，固溶化溫度中，δ肥粒鐵相分率和固溶化溫度與持溫時間均呈現正相關，而肥粒鐵的比例則和硬度呈負相關。第二部分，欲將不銹鋼軟化，施以640℃~790℃溫度的退火熱處理，發現在690℃以上時有M23C6與M23(C,B)6析出，當退火溫度740℃以上時在δ肥粒鐵相晶界處有Laves phase析出；除此之外在退火溫度740℃以上時來到了(α+γ)雙相區中，γ相和退火溫度與持溫時間呈現正相關，而γ相冷卻後形成麻田散鐵，使硬度提升，所以欲將13Cr2Ni2Mo不銹鋼退火軟化，應避免退火溫度超過(α+γ)雙相區溫度。 This study is focused on a 13Cr2Ni2Mo stainless steel use as screws manufacturing. We want to find the best heat treatment parameters for manufacturing, by analysising it’s microstructure and hardness. The first part of my experiment is solid solution heat treatment.In this stage,the microstructure is martensite as a base phase with some δ ferrite phase. When temperature of solid solution heat treatment is 1100 ℃,and temperature holding time is less than 30 minutes, there is still B-rich Mo-rich phase undissolved back to base; The fraction of δ ferrite phases are positive related with temperature and holding time, but the fraction of the ferrite is negative related with hardness in 1100℃~ 1200℃. The second part, we want to soften the stainless steel. So we anneal it by 640 ℃ ~ 790 ℃.We found that when annealing temperature higher than 690℃,there are M23C6 and M23 (C,B)6 precipitated.When temperature higher than 740℃,Laves phase is precipitated on δ ferrite grain boundaries. When the annealing temperature above 740 ℃ ,it comes to the (α + γ) two-phase region. γ phase is positive related with the annealing temperature and the annealing holding time. The γ-phase transform to martensite at room temperature, and martensite make hardness upgrade. So, to soften 13Cr2Ni2Mo stainless steel should avoid the annealing temperature exceeds (α + γ) two-phase zone.

固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 = Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel
林, 承毅

固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 = Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel / 林承毅撰 - [高雄市] : 國立高雄大學, 2015[民104]. - [10]，109葉 ; 圖，表 ; 30公分.
109年11月18日公開.
參考書目：葉92-98.
13Cr2Mo2Ni不銹鋼13Cr2Mo2NiStainless Steel

固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 = Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel
LDR:03703nam0a2200277 450 001 458243
005 20220310133825.0
010 0 $b 精裝
010 0 $b 平裝
100 $a 20151007d2015 k y0chiy50 e
101 0 $a chi $d chi $d eng
102 $a tw
105 $a ak am 000yy
200 1 $a 固溶化及退火熱處理對13Cr2Ni2Mo不鋼顯微組織之影響 $d Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel $z eng $f 林承毅撰
210 $a [高雄市] $c 國立高雄大學 $d 2015[民104]
215 0 $a [10]，109葉 $c 圖，表 $d 30公分
300 $a 109年11月18日公開
314 $a 指導教授：林東毅教授
320 $a 參考書目：葉92-98
328 $a 碩士論文--國立高雄大學化學工程及材料工程學系碩士班
330 $a 本論文研製之新型不銹鋼13Cr2Mo2Ni，欲將此材料應用螺絲製造業，針對其組織與硬度分析，研究適合加工的熱處理參數。本實驗分為兩個部分，第一部分為固溶化熱處理，此階段顯微組織主要為基地相的麻田散鐵，以及δ肥粒鐵相，在1100℃持溫時間30分鐘內時，仍有富硼富鉬相未固溶回基地中；在1100℃~1200℃，固溶化溫度中，δ肥粒鐵相分率和固溶化溫度與持溫時間均呈現正相關，而肥粒鐵的比例則和硬度呈負相關。第二部分，欲將不銹鋼軟化，施以640℃~790℃溫度的退火熱處理，發現在690℃以上時有M23C6與M23(C,B)6析出，當退火溫度740℃以上時在δ肥粒鐵相晶界處有Laves phase析出；除此之外在退火溫度740℃以上時來到了(α+γ)雙相區中，γ相和退火溫度與持溫時間呈現正相關，而γ相冷卻後形成麻田散鐵，使硬度提升，所以欲將13Cr2Ni2Mo不銹鋼退火軟化，應避免退火溫度超過(α+γ)雙相區溫度。 This study is focused on a 13Cr2Ni2Mo stainless steel use as screws manufacturing. We want to find the best heat treatment parameters for manufacturing, by analysising it’s microstructure and hardness. The first part of my experiment is solid solution heat treatment.In this stage,the microstructure is martensite as a base phase with some δ ferrite phase. When temperature of solid solution heat treatment is 1100 ℃,and temperature holding time is less than 30 minutes, there is still B-rich Mo-rich phase undissolved back to base; The fraction of δ ferrite phases are positive related with temperature and holding time, but the fraction of the ferrite is negative related with hardness in 1100℃~ 1200℃. The second part, we want to soften the stainless steel. So we anneal it by 640 ℃ ~ 790 ℃.We found that when annealing temperature higher than 690℃,there are M23C6 and M23 (C,B)6 precipitated.When temperature higher than 740℃,Laves phase is precipitated on δ ferrite grain boundaries. When the annealing temperature above 740 ℃ ,it comes to the (α + γ) two-phase region. γ phase is positive related with the annealing temperature and the annealing holding time. The γ-phase transform to martensite at room temperature, and martensite make hardness upgrade. So, to soften 13Cr2Ni2Mo stainless steel should avoid the annealing temperature exceeds (α + γ) two-phase zone.
510 1 $a Effect of solid solution and annealing on microstructure of 13Cr2Ni2Mo stainless steel $z eng
610 # 0 $a 13Cr2Mo2Ni不銹鋼 $a 固溶化熱處理 $a 退火熱處理 $a M23C6 $a M23(C.B)6 $a Laves phase
610 # 1 $a 13Cr2Mo2NiStainless Steel $a solid solution heat treatment $a annealing heat treatment $a M23C6 $a M23(C.B)6 $a Laves phase
681 $a 008M/0019 $b 541208 4410 $v 2007年版
700 1 $a 林 $b 承毅 $4 撰 $3 709499
712 0 2 $a 國立高雄大學 $b 化學工程及材料工程學系碩士班 $3 353898
801 0 $a tw $b NUK $c 20201109 $g CCR
856 7 # $u https://hdl.handle.net/11296/76mn5y $z 電子資源 $2 http