國立高雄大學圖資館 |

Language: English

Back

Network of things engineering (NoTE) lab

Record Type:	Electronic resources : Monograph/item
Title/Author:	Network of things engineering (NoTE) labby Admela Jukan ... [et al.].
other author:	Jukan, Admela.
Published:	Cham :Springer International Publishing :2023.
Description:	xxiii, 198 p. :ill. (some col.), digital ;24 cm.
Contained By:	Springer Nature eBook
Subject:	Internet of things.
Online resource:	https://doi.org/10.1007/978-3-031-20635-1
ISBN:	9783031206351$q(electronic bk.)

Network of things engineering (NoTE) lab
Network of things engineering (NoTE) lab[electronic resource] /by Admela Jukan ... [et al.]. - Cham :Springer International Publishing :2023. - xxiii, 198 p. :ill. (some col.), digital ;24 cm.

Chapter 1. Introduction -- Chapter 2. NoteLab setup requirements -- Chapter 3. Lab 0 - Getting started -- Chapter 4. Lab 1 - Interfacing sensors and actuators -- Chapter 5. Lab 2 - Connecting IoT and Edge with MQTT -- Chapter 6. Lab 3 - Connecting edge and cloud tools with AMQP -- Chapter 7. Lab 4 - Connecting edge and cloud tools with REST HTTP -- Chapter 8. Lab 5 - Prototyping data connectors -- Chapter 9. Lab 6 - Integrating sensors and actuators with edge and cloud tools -- Chapter 10. Lab 7 - Network-of-Things final setup.

This book provides a hands-on experience in software and hardware engineering of IoT devices in edge and cloud computing systems, by putting in practice state-of-the-art concepts of hardware devices, networking and computing software. It proposes a Network of Things Engineering (NoTE) Lab, with seven hands-on lab modules covering topics ranging from "Interfacing sensors and actuators" and "Connecting IoT and Edge with MQTT" to "Data pipelining in cloud computing". All tools and software used in the NoTE Lab are free and open source, and available to the readers. Specifically, Arduino-based boards that support a variety of low-cost sensors and actuators are used in IoT context. In edge computing, NoTE Lab implements off-the-shelf single board computers, Raspberry Pis with corresponding software and hardware. For cloud, well-known and widely used cloud computing open-source tools (e.g., Kubernetes) are deployed, where readers can learn the basics of monitoring and managing containers in cloud computing. Three communication protocols are used in the end-to-end setup, including MQTT, AMQP and HTTP. This lab book is a "must experiment with" for anybody in academia and industry participating in the fascinating IoT-edge-cloud continuum development.

ISBN: 9783031206351$q(electronic bk.)

Standard No.: 10.1007/978-3-031-20635-1doiSubjects--Topical Terms:

670954
Internet of things.

LC Class. No.: TK5105.8857

Dewey Class. No.: 004.678

Network of things engineering (NoTE) lab
LDR:02769nmm a2200325 a 4500 001 643053
003 DE-He213
005 20230421072039.0
006 m d
007 cr nn 008maaau
008 231123s2023 sz s 0 eng d
020 $a 9783031206351$q(electronic bk.)
020 $a 9783031206344$q(paper)
024 7 $a 10.1007/978-3-031-20635-1 $2 doi
035 $a 978-3-031-20635-1
040 $a GP $c GP
041 0 $a eng
050 4 $a TK5105.8857
072 7 $a UT $2 bicssc
072 7 $a TEC007000 $2 bisacsh
072 7 $a UT $2 thema
082 0 4 $a 004.678 $2 23
090 $a TK5105.8857 $b .N476 2023
245 0 0 $a Network of things engineering (NoTE) lab $h [electronic resource] / $c by Admela Jukan ... [et al.].
260 $a Cham : $b Springer International Publishing : $b Imprint: Springer, $c 2023.
300 $a xxiii, 198 p. : $b ill. (some col.), digital ; $c 24 cm.
505 0 $a Chapter 1. Introduction -- Chapter 2. NoteLab setup requirements -- Chapter 3. Lab 0 - Getting started -- Chapter 4. Lab 1 - Interfacing sensors and actuators -- Chapter 5. Lab 2 - Connecting IoT and Edge with MQTT -- Chapter 6. Lab 3 - Connecting edge and cloud tools with AMQP -- Chapter 7. Lab 4 - Connecting edge and cloud tools with REST HTTP -- Chapter 8. Lab 5 - Prototyping data connectors -- Chapter 9. Lab 6 - Integrating sensors and actuators with edge and cloud tools -- Chapter 10. Lab 7 - Network-of-Things final setup.
520 $a This book provides a hands-on experience in software and hardware engineering of IoT devices in edge and cloud computing systems, by putting in practice state-of-the-art concepts of hardware devices, networking and computing software. It proposes a Network of Things Engineering (NoTE) Lab, with seven hands-on lab modules covering topics ranging from "Interfacing sensors and actuators" and "Connecting IoT and Edge with MQTT" to "Data pipelining in cloud computing". All tools and software used in the NoTE Lab are free and open source, and available to the readers. Specifically, Arduino-based boards that support a variety of low-cost sensors and actuators are used in IoT context. In edge computing, NoTE Lab implements off-the-shelf single board computers, Raspberry Pis with corresponding software and hardware. For cloud, well-known and widely used cloud computing open-source tools (e.g., Kubernetes) are deployed, where readers can learn the basics of monitoring and managing containers in cloud computing. Three communication protocols are used in the end-to-end setup, including MQTT, AMQP and HTTP. This lab book is a "must experiment with" for anybody in academia and industry participating in the fascinating IoT-edge-cloud continuum development.
650 0 $a Internet of things. $3 670954
650 1 4 $a Internet of Things. $3 913131
650 2 4 $a Electronic Circuits and Systems. $3 913394
650 2 4 $a Computer Engineering and Networks. $3 913124
700 1 $a Jukan, Admela. $3 950567
710 2 $a SpringerLink (Online service) $3 273601
773 0 $t Springer Nature eBook
856 4 0 $u https://doi.org/10.1007/978-3-031-20635-1
950 $a Engineering (SpringerNature-11647)